Doubling (textiles)
Doubling is a textile industry term synonymous with combining. It can be used for various processes during spinning. During the carding stage, several sources of roving are doubled together and drawn, to remove variations in thickness. After spinning, yarn is doubled for many reasons. Yarn may be doubled to produce warp for weaving, to make cotton for lace, crochet and knitting. [1] It is used for embroidery threads and sewing threads, for example: sewing thread is usually 6-cable thread. Two threads of spun 60s cotton are twisted together, and three of these double threads are twisted into a cable, of what is now 5s yarn. This is mercerised, gassed (AKA flamed) and wound onto a bobbin. [2]
Processing of cotton
 | ||||||
| Bale Breaker | Blowing Room | |||||
 |  |  | ||||
| Willowing |  | |||||
| | |||||
| Breaker Scutcher | Batting | |||||
| | |||||
| Finishing Scutcher | Lapping | |||||
 |  |  | ||||
| Carding | Carding Room | |||||
| | | ||||
| Sliver Lap | | |||||
| | |||||
| Combing | | |||||
| | | ||||
| Drawing | ||||||
| ||||||
| Slubbing | ||||||
| ||||||
| Intermediate | ||||||
| ||||||
| Roving | | Fine Roving | ||||
| |  | ||||
| Mule Spinning | - | Ring Spinning | Spinning | |||
| | | ||||
| |  | | | ||
| Reeling |  | Doubling | |||
| | | ||||
| Winding | Bundling | Bleaching | ||||
| |  | | |||
| Weaving shed |  | Winding | ||||
| | | ||||
| Beaming | | Cabling | ||||
| | | ||||
| Warping | | Gassing | ||||
| | | ||||
| Sizing/Slashing/Dressing | | Spooling | ||||
| | | ||||
| Weaving | | | ||||
|  | | ||||
| Cloth | Yarn (Cheese)- - Bundle | Sewing Thread |
Doubling in the carding process
In a wider sense carding can refer to the four processes of willowing, lapping, carding and drawing. During willowing the fibres are loosened; in lapping the dust is removed to create a flat sheet or lap of fibres. Carding combs the tangled lap into a thick rope or sliver of 1/2 inch in diameter, and removes the shorter fibres creating a stronger yarn.
During the carding process the staples are separated and then assembled into a loose strand (sliver or tow). The carders line up the staples to prepare them for spinning. The carding machine consists mainly of one big roller with smaller ones surrounding it. All of the rollers are covered in small teeth, and as the cotton progresses further on the teeth get finer (i.e. closer together). The cotton leaves the carding machine in the form of a sliver; a large rope of fibres.[3]
In drawing, 4 slivers are combined into one. Repeated drawing increases the quality of the sliver allowing for finer counts to be spun.[4] Each sliver will have thin and thick spots. By combining, or doubling several slivers together a more consistent size can be reached. The slivers are separated into rovings. These rovings (or slubbings) are then what are used in the spinning process. [5]
For machine processing, a roving is about the width of a pencil. The rovings are collected in a drum and proceed to the slubbing frame which adds twist, and winds onto bobbins. Intermediate Frames are used to repeat the slubbing process to produce a finer yarn, and then the roving frames reduces it to a finer thread, gives more twist, makes more regular and even in thickness, and winds onto a smaller tube.[6]
Over time the processes were refined. At Masson Mill and at Helmshore, there are Derby Doublers. The Masson machine, built by Platts of Oldham in 1902, doubled rovings from the breaker cards into card lap. This was then passed through the finisher card to produce the rovings [7] This process was known as double carding. The Derby Doubler was patented by Evan Leigh of Ashton-underline (21 December 1810 - 2 February 1876) and, though superseded, still continued in service in condensing coarse counts.[8]
The doubling process
Doubling of yarn where two or more stands or ends of yarn are twisted together. There are many purposes where doubled yarn is used. Sometimes thread is doubled to make warp, and it is invariably used for the manufacture of knitting yarn, crochet yarn and sewing yarn. All these yarns must be smooth and free from knots. In a sewing thread, the treads are doubled in two phases. Two or three strands are twisted together then three of theses threads are twisted together, to form a six or nine cord.[9] The spun yarn is wound onto a bobbin using a doubling winding machine, and two or more of these bobbins are placed on doubling frame (doubling winding machine). The ends pass through a series of rollers and twisted together onto one bobbin using a spindle and flyer. The process here is similar to that found in one of Arkwrights Water frames, though the size of the ring, spindle and traveller are predictably larger. Alternatively a 'twiner' is used: this is a modified spinning mule and is mainly consigned to the doubling of warp thread [10] High quality doubling depended on keeping the tension correct and feeding the produced thread evenly and tightly on a bobbin or flangeless paper tubes [11]
References
- Notes
- ↑ Naismith 1896, p. 557.
- ↑ Naismith 1896, p. 567.
- ↑ Collier 1970, pp. 66,67
- ↑ Collier 1970, p. 69
- ↑ Collier 1970, pp. 70
- ↑ Hills 1993, p. 4
- ↑ Masson Mill Derby Doubler
- ↑ One guy from Barlick: Evan Leigh and the Derby Doubler Stanley Graham
- ↑ Naismith 1896, pp. 58.
- ↑ Naismith 1896, p. 564.
- ↑ Naismith 1896, p. 562.
- Bibliography
- Collier, Ann M (1970), A Handbook of Textiles, Pergamon Press, p. 258, ISBN 0-08-018057-4
- Nasmith, Joseph (1896), The Students'Cotton Spinning (3 ed.), Manchester: John Heywood, p. 638
- Hills, Richard Leslie (1993), Power from Steam: A History of the Stationary Steam Engine, Cambridge University Press, p. 244, ISBN 978-0-521-45834-4, retrieved January 2009 Check date values in:
|access-date=(help)