Motronic

Motronic is the trade name given to a range of digital engine control units developed by Robert Bosch GmbH (commonly known as Bosch) which combined control of fuel injection and ignition in a single unit. By controlling both major systems in a single unit, many aspects of the engine's characteristics (such as power, fuel efficiency, drivability, and emissions) can be improved.

Motronic ML1.x

ML1.0

Often known as "Motronic basic", Motronic ML1.x was one of the first digital engine-management systems developed by Bosch. These early Motronic systems integrated the spark timing element with then-existing Jetronic fuel injection technology. It was originally developed and first used in the BMW 7-Series,[1] before being implemented on several Volvo[2] and Porsche[3] engines throughout the 1980s.

The components of the Motronic ML1.x systems for the most part remained unchanged during production, although there are some differences in certain situations. The engine control module (ECM) receives information regarding engine speed, crankshaft angle, coolant temperature and throttle position. An air flow meter also measures the volume of air entering the induction system.

If the engine is naturally aspirated, an air temperature sensor is located in the air flow meter to work out the air mass. However, if the engine is turbocharged, an additional charge air temperature sensor is used to monitor the temperature of the inducted air after it has passed through the turbocharger and intercooler, in order to accurately and dynamically calculate the overall air mass.

Main system characteristics

ML1.1

The Motronic 1.1 System was used by BMW from 1987 on motors such as the M20.

The systems have the option for a lambda sensor, enabling their use with catalytic converter-equipped vehicles. This feedback system allows the system analyse exhaust emissions so that fuel and spark can be continually optimised to minimise emissions. Also present is adaptive circuitry, which adjusts for changes in an engine's characteristics over time. Some PSA engines also include a knock sensor for ignition timing adjustment,[4] perhaps this was achieved using an external Knock Control Regulator.

The Motronic units have 2 injection outputs, and the injectors are arranged in 2 "banks" which fire once every two engine revolutions. In an example 4-cylinder engine, one output controls the injectors for cylinders 1 and 3, and the other controls 2 and 4. The system uses a "cylinder ID" sensor mounted to the cam-shaft to detect which cylinders are approaching the top of their stroke, therefore which injector bank should be fired. During start-up (below 600 RPM), or if there is no signal from the cylinder ID sensor, all injectors are fired simultaneously once per engine revolution.[5] In BMW vehicles, this Motronic version did not have a cylinder ID and as a result, both banks of injectors fired at once.

ML1.3

Motronic 1.1 was superseded in 1988 by the Motronic 1.3 system[5] that was also used by PSA on some XU9J-series engines (which previously used Motronic 4.1).[4] and by BMW.

The Motronic 1.1 and 1.3 systems are largely similar, the main improvement being the increased diagnostic capabilities of Motronic 1.3. The 1.3 ECM can store many more detailed fault codes than 1.1, and has a permanent 12-volt feed from the vehicle's battery which allows it to log intermittent faults in memory across several trips. Motronic 1.1 can only advise of a few currently-occurring faults.[5]

M1.5

This system was used on some of General Motors Family II engines (C20NE, 20NE, C20SE, 20SE, 20SEH, 20SER, C20NEF, C20NEJ, C24NE, C26NE, C30LE, C30NE, C30SE, C30SEJ, C30XEI). The system is very reliable and problems encountered are usually caused by poor contact at the associated plug/socket combinations that link the various system sensors to the Electronic Control Unit (ECU). Predecessor of the ME Motronic. Also uses in the Opel engines C16SEI

M1.5.2

Was used since 1991 in the Opel Astra F with C20NE engine. Major change was the use of a MAF instead of AFM in the Motronic 1.5.

M1.5.4

Was used since 1994 in the Opel Omega B with X20SE engine. (Modified successor of C20NE engine) Major change to the Motronic 1.5.2 was the use of DIS ignition system and knock sensor. Was also uses in the Opel engine X22XE.

M1.7

The key feature of Motronic 1.7 is the elimination of an ignition distributor, where instead each cylinder has its own electronically-triggered ignition coil. Motronic 1.7 family has versions 1.7, 1.7.2, 1.7.3, all of them used on M42/M43 engines in BMW 3 Series (E36) up to 1998[6] and BMW 5 Series (E34) up to 1995.[7] The BMW M70 12 cylinder had the Motronic M1.7 and two distributor.

M1.8

This system was used by Volvo on some Volvo 960 cars.[8]

M2.5

Was introduced in 1988 in the Opel Kadett E GSi 16V C20XE engine. Sequential fuel injection and knock control.

M2.8

Successor of the Motronic 2.5. Was used from 1992 at Opel C20XE engine. Major change was the introduction of DIS ignition. Was also at Opel V6 engine C25XE used. Modified as M2.8.1, M2.8.3 at Opel V6 engine X25XE and X30XE.

Motronic ML 2.1 Series

The ML 2.1 system integrates an advanced engine management with 2 knock sensors provision for adaptive fuel & timing adjustment, purge canister control, precision sequential fuel control & diagnostics (pre OBD-1). Fuel enrichment during cold-start is achieved by altering the timing of the main injectors based on engine temperature. The idle speed is also fully controlled by the digital Motronic unit, including fast-idle during warm-up. Updated variants ML 2.10.1 thru 2.5 add MAF Mass Air Flow sensor logic and direct fire ignition coils per cylinder. Motronic 2.1 is used in the Porsche 4 cyl 16V 944S/S2/968 and the 6 cyl Boxer Carrera 964 & 993, Opel/Vauxhall, FIAT & Alfa Romeo engines.

Motronic ML 3.1

Compared with ML1.3, this system adds knock sensor control, purge canister control and start-up diagnostics. Motronic 3.1 is used in early BMW M50 engines.[9]

Motronic ML4.X

Motronic ML4.1

The Motronic 4.1 system was used on Opel / Vauxhall eight-valve engines from 1987–1990,[10] alfa romeo and some PSA Peugeot Citroën XU9J-series engines.[4]

Fuel enrichment during cold-start is achieved by altering the timing of the main injectors based on engine temperature, no "cold start" injector is required. The idle speed is also fully controlled by the Motronic unit, including fast-idle during warm-up (therefore no thermo-time switch is required).

The 4.1 system did not include provision for a knock sensor for timing adjustment. The ignition timing and fuel map could be altered to take account of fuels with different octane ratings by connecting a calibrated resistor (taking the form of an "octane coding plug" in the vehicle's wiring loom) to one of the ECU pins, the resistance depending on the octane adjustment required.[10] With no resistor attached the system would default to 98 octane.

There is a single output for the injectors, resulting in all injectors firing simultaneously. The injectors are opened once for every revolution of the engine, injecting half the required fuel each time.[10]

Motronic ML4.1 was used in the Opel engines: 20NE, 20SE, 20SEH, 20SER, C20NE, C30LE, C30NE.

Motronic M4.3

The Motronic 4.3 was used by Volvo for their five-cylinder turbocharged 850 models from 1993 until 1996.

It was introduced with the launch of the 850 Turbo (also called the 850 T-5 and 850 T-5 Turbo) in October 1993[11] for model year 1994. Features included OBD I diagnostics, dual knock sensors and a lot more. For the 1996 model year OBD II diagnostics were introduced on some cars while M4.3 was beginning to be phased out. The last M4.3 equipped cars were made for modelyear 1997.[12]

Motronic M4.4

The Motronic 4.4 was used by Volvo from 1996 until 1998.

The M 4.4 was based on its predecessor and featured only a small number of improvements. Memory capacity was doubled and a few new functions introduced such as immobilizer compatibility. OBD II was standard on all cars fitted with this system albeit the necessary protocolls were not integrated for all markets. The system was used for the five and six cylinder modular engined cars and was used on turbocharged and naturally aspirated models. Introduced in 1996 for 1997 model year it was first installed on some of the last 850 models[12][13] like the 2.5 20V and AWD. A coil on plug variant existed for the six cylinder Volvo 960/S90/V90,.[12][14] After the 850 was replaced by the Volvo V70,[15] Volvo S70[16] and Volvo C70 the system was used until the end of model year 1998.[14]

See also

References

This article is issued from Wikipedia - version of the 7/16/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.