Xiaolin Wu's line algorithm

Demonstration of Xiaolin Wu's algorithm

Xiaolin Wu's line algorithm is an algorithm for line antialiasing, which was presented in the article An Efficient Antialiasing Technique in the July 1991 issue of Computer Graphics, as well as in the article Fast Antialiasing in the June 1992 issue of Dr. Dobb's Journal.

Bresenham's algorithm draws lines extremely quickly, but it does not perform anti-aliasing. In addition, it cannot handle any cases where the line endpoints do not lie exactly on integer points of the pixel grid. A naive approach to anti-aliasing the line would take an extremely long time. Wu's algorithm is comparatively fast, but is still slower than Bresenham's algorithm. The algorithm consists of drawing pairs of pixels straddling the line, each coloured according to its distance from the line. Pixels at the line ends are handled separately. Lines less than one pixel long are handled as a special case.

An extension to the algorithm for circle drawing was presented by Xiaolin Wu in the book Graphics Gems II. Just like the line drawing algorithm is a replacement for Bresenham's line drawing algorithm, the circle drawing algorithm is a replacement for Bresenham's circle drawing algorithm.

Algorithm

function plot(x, y, c) is
    plot the pixel at (x, y) with brightness c (where 0  c  1)

// integer part of x
function ipart(x) is
    return int(x)

function round(x) is
    return ipart(x + 0.5)

// fractional part of x
function fpart(x) is
    if x < 0
        return 1 - (x - floor(x))
    return x - floor(x)

function rfpart(x) is
    return 1 - fpart(x)

function drawLine(x0,y0,x1,y1) is
    boolean steep := abs(y1 - y0) > abs(x1 - x0)
    
    if steep then
        swap(x0, y0)
        swap(x1, y1)
    end if
    if x0 > x1 then
        swap(x0, x1)
        swap(y0, y1)
    end if
    
    dx := x1 - x0
    dy := y1 - y0
    gradient := dy / dx
    
    // handle first endpoint
    xend := round(x0)
    yend := y0 + gradient * (xend - x0)
    xgap := rfpart(x0 + 0.5)
    xpxl1 := xend // this will be used in the main loop
    ypxl1 := ipart(yend)
    if steep then
        plot(ypxl1,   xpxl1, rfpart(yend) * xgap)
        plot(ypxl1+1, xpxl1,  fpart(yend) * xgap)
    else
        plot(xpxl1, ypxl1  , rfpart(yend) * xgap)
        plot(xpxl1, ypxl1+1,  fpart(yend) * xgap)
    end if
    intery := yend + gradient // first y-intersection for the main loop
    
    // handle second endpoint
    xend := round(x1)
    yend := y1 + gradient * (xend - x1)
    xgap := fpart(x1 + 0.5)
    xpxl2 := xend //this will be used in the main loop
    ypxl2 := ipart(yend)
    if steep then
        plot(ypxl2  , xpxl2, rfpart(yend) * xgap)
        plot(ypxl2+1, xpxl2,  fpart(yend) * xgap)
    else
        plot(xpxl2, ypxl2,  rfpart(yend) * xgap)
        plot(xpxl2, ypxl2+1, fpart(yend) * xgap)
    end if
    
    // main loop
    if steep then
        for x from xpxl1 + 1 to xpxl2 - 1 do
           begin
                plot(ipart(intery)  , x, rfpart(intery))
                plot(ipart(intery)+1, x,  fpart(intery))
                intery := intery + gradient
           end
    else
        for x from xpxl1 + 1 to xpxl2 - 1 do
           begin
                plot(x, ipart(intery),  rfpart(intery))
                plot(x, ipart(intery)+1, fpart(intery))
                intery := intery + gradient
           end
    end if
end function

References

This article is issued from Wikipedia - version of the 6/15/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.